Selasa, 05 Maret 2013 - 1 komentar

SERVICE MODE TV SHARP

BCTVA Chassis
66AS06H, DV5932H, DV5935H, DV5937H and DV6635H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire


Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

4BS-C Chassis
DV5940H, DV6640H and 66AS05H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Text Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire
 
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

CA1 Chassis
37DM23H, 37DT25H, 37ET35H, 37EM33H and 51DT25H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote control

CA10 Chassis
51DS02H, 51DS03H, 51DS05H, 59DS03H, 59DS05H, 59ES03H, 59ES05H, 59ESD7H, 66DS03H, 66DS05H,
66ES05H and 66ESD7H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

CS Chassis
51CS03H, 51CS05H, 59CS03H, 59CS05H, 59CSD8H, 66CS03H, 66CS05H and 66CSD8H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

CW100 Chassis
66DW18H and 76DW18H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

D3000 Chassis
DV51083H, DV5903H, DV59083H, DV6603H and DV66083H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB

Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode

4BS-B Chassis
DV5165H and DV5180H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

DECO-4 and DECO-5 Chassis
DV5105H (DECO-4), DV5107H, DV5132H and DV5135H (DECO-5)
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen

Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode

4BSA Chassis
DV3760H, DV3770H and DV5161H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire
To select an adjustment use the channel up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.

5BSA Chassis
37AM12H, 37AM23H, 37AT25H and 51AT15H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode - 'SERV' appears on the screen
7. Release the two buttons


Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off

S3B Chassis
DV3750H, DV3751H, DV5131H and DV5150H
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wir


Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.

1 komentar:

Noora Amalie 28 Juni 2020 pukul 18.25

The post is written in very a good manner and it contains much useful information for me. If you are interested in Pop Up Tents, please check the link.

Posting Komentar